Loving the vintage vibe!

Here's where I'll share my obsession with vintage fabric! It's taking over my house!

I'll sharing with you my favorite fabrics, my 'adventures" in dressmaking using vintage patterns, some home furnishing ideas and no doubt I'll be telling you about any exciting finds! Love to hear about your vintage adventures too!

My first Shop was AudreysCat ( online shop May 2010) , but my new logo / name - WittyDawn , arrived Jan 2014.

I hope you'll have time to browse my shops too !

Friday, 27 February 2015

A little revamp DIY project - Footstool Makeover!

A very satisfying and quite quick revamp / renewal of this little footstool
From this rather sad looking thing ... to this smart little stool with a super vintage Sanderson fabric :)

I really should have taken more pictures of the stages involved BUT if you are interested this is what I did ....




1. Remove feet and strip bank to wood - the old foam etc was rather yucky and NOT for reusing! I didn't bother removing all the tacks on the edges of the wood base as I had a cunnng plan to cover them up and in any case was going to use a staple gun to tack fabric on underneath the stool .
2. I used the wood base  to create a circle tamplate - I used this to cut foam, the polyester wadding circle/strip, and the lining fabric circle and strip and another circle of fabric to sew on underneath to cover up base at the end . I made sure that the side strips of wadding and lining fabric had a generous overlap of fabric to allow them to be stapled to underside of stool base - about 5cm deeper than foam.
3. I handstitched the circle of wadding and side strip of wadding over the foam - now you COULD just use foam by itself BUT the wadding gives a smoother finish - also any roughness in foam edges is masked AND those tacks that I couldn't be bothered to prise off are also covered up :)
4. I machined sewed together the circle and strip of lining fabric - I always prefer to line upholstery projects like this but you could just put your top fabric straight on. You could just use one piece of lining fabric and staple it on BUT if you fit the lining fabric it minimises the pleating/fabric gathers when you come to staple it on-  I think it results in a smoother final finish.
5. Making sure I had a reasonably tight fit I put foam on base , put lining cover on and stapled it on with an upholstery staple gun ( such a useful bit of kit!). Staple underneath at one point first , then pulling fabric fairly tauntly/firmly directly opposite staple again. Do the same but at right angled to you first pair of fixings - so basically you have staple at each quarter of the circle ( sorry this is a bit of a rubbish explanation! you then can work between each set of staples aimimg for lots of small gathers/pleats, rather that one or two larger ones, to get a smooth a finish as you can. What you DON'T do is start stapling at one point and work your way round! you will end up with a huge wad of excess fabric at the end - trust me on this....
6. Then I stapled on my top fabric in same way ( a great vintage Sandersons one - was actually an apron when it came to me!) and trimmed off excess fabric underneath . You will see that I didn't make a fitted cover as I wanted  a single piece of fabric to show off the design. You do have to do a bit more gathering and pleating but it's not difficult if you remember to do lots of small ones :)
7. Finishing time ! I hand sewed a hemmed circle of lining fabric underneath covering up raw edges of wadding/lining/fabric /staples. I then had this very pretty embriodered/scalloped edged floral bias binding which I hand sewed on the bottom edge - it didn't NEED this to cover up anything but it is a good finishing touch. I screwed legs back on through the lining fabric underneath - ALL DONE

When I read it back this looks like a lot of work - it really isn't ! although if you aren't keen on handsewing ( I like it) you might want to skip some of the finishing BUT in my opinion it is those bits that make for a neatly finished project.

No comments:

Post a Comment

Thanks for your comment , it will be published shortly...